How to Set up a Bathtub Yourself
How to Set up a Bathtub Yourself
Blog Article
Presented here down the page you can get more decent data concerning How to Install a Bathtub.
Mounting a tub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is conveniently accessible, the task can move quickly; if you have to open a wall surface to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the task as well as fit attempting it. Rather than hiring a professional to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you might require an expert plumber to make tube links.
This post will assist you set up a new bathtub in your restroom if you have actually currently purchased a new tub and don't require to transform the setup of your previous water system pipelines.
Your tools as well as material checklist must make up the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to stop pressure on the tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water system and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub and likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, deal with the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub must wait till the bath tub has been utilized a minimum of once as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very interested in How to Install a Bathtub and I really hope you enjoyed reading my page. In case you appreciated our post plz be sure to share it. Thanks a lot for taking the time to read it.
Course Detail
Report this page